Welker AD905BP Installation, Operation And Maintenance Manual Download Page 34 | Manualshive

Page: 34 / 47

background image

34

IOM-189

MODEL: INFLOW™ ACE MANUAL INSERTION

REV: G

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Disassembling the Upper Housing

20.

If the inFlow™ ACE is not equipped with the optional external adjustment, continue to step 21. If the inFlow™ ACE is
equipped with the optional external adjustment, proceed to step 23.

Without Optional External Adjustment Assembly

21.

Unscrew the bolts from the top cap and carefully remove the top cap from the motor housing (

22.

Proceed to step 27.

With Optional External Adjustment Assembly

Figure 20: External Adjustment Assembly

23.

Unscrew the motor top from the motor housing.

24.

Carefully remove the motor top from the external adjustment body.

25.

Carefully unscrew the external adjustment body from the insertion shaft. Note that the external adjustment rings will
remain attached to the external adjustment body and will also be removed at this time.

26.

Unscrew the cap screws from the top cap and carefully remove the top cap from the motor housing (

27.

Unscrew the setscrews from the base of the packing gland body (

28.

Unscrew the packing gland body from the outer shaft.

29.

Unscrew the packing gland body from the motor housing, and then carefully remove the packing gland body from the
insertion shaft. Take care not to scratch or otherwise damage the insertion shaft.

30.

Carefully pull the insertion shaft out through the motor housing.

«
...
32
33
34
35
36
...
»

Summary of Contents for AD905BP
















































Reviews:

No comments

Related manuals for AD905BP

Brand: A&D Pages: 74

Brand: Gazelle Pages: 2

Brand: Make Noise Pages: 15

Brand: Major tech Pages: 40

Brand: E Instruments Pages: 144

Brand: Hama Pages: 16

Brand: Yamaha Pages: 12

Brand: Endress+Hauser Pages: 24

Brand: Novus Pages: 52

Brand: Rockler Pages: 4

Solar Auxiliary Power Unit

Brand: J-TECH Pages: 6

Brand: Lumel Pages: 32

Brand: OHAUS Pages: 64

Brand: Würth Pages: 28

Brand: b&o Pages: 32

Brand: SMPE Pages: 2

Brand: Omni Instruments Pages: 8

Brand: Schaller Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands