Welker AD905BP Installation, Operation And Maintenance Manual Download Page 30

Page: 30 / 47

IOM-189

MODEL: INFLOW™ ACE MANUAL INSERTION

REV: G

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

3.2 Maintenance: Optional Insertion Tool

Prior to performing maintenance on the optional insertion tool, the inFlow™ ACE must be removed from the pipeline.
See

Section 2.8, Retracting the Unit,

for instructions on retracting the insertion shaft and removing the inFlow™ ACE from

the pipeline.

Lay the inFlow™ ACE on a smooth, clean surface with the tube fittings facing up.

Removing the Insertion Tool

Figure 16: Insertion Tool Diagram

Remove the hex nuts, flat washers, and lock washers from the top of each insertion tool shaft and upper bracket
standoff.

Remove the top brackets.

Unscrew the fastener screws from the upper bracket plate, and then loosen the front fastener screw on the upper
bracket.

Holding the upper bracket standoffs, carefully lift the stabilizer bar and upper bracket from the motor housing.

Remove the bracket bolts from the lower bracket.

Unscrew the fastener screws from the lower bracket plate, and then loosen the front fastener screw on the lower
bracket.

Holding both insertion tool housings, carefully lift the lower bracket from the lubricator body. Note that the lower
bracket will remain attached to the insertion tool housings.

Summary of Contents for AD905BP
















































Search results

Summary of Contents for AD905BP

Reviews:

Related manuals for AD905BP

Brands by name

Popular brands

Welker AD905BP, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for AD905BP

Reviews:

Related manuals for AD905BP

Brands by name

Popular brands