Welch Allyn IMAGETEAM 3800 Page 22 User Manual Download

Page: 22 / 132

IMAGETEAM 3800 User’s Guide

2–8

Serial Port Connection

All communication parameters between the scanner and terminal must match
for correct data transfer through the serial port using RS-232 protocol. Scan
the RS-232 Interface bar code to program the scanner for an RS-232
installation.

RS-232 Interface

1. Turn off power to the terminal/computer.
2. Connect the appropriate interface cable to the scanner, as shown below.

Note:

For the scanner to work properly, you must have the correct

cable for your type of terminal/computer.

3. Plug the serial connector into the serial port on the back of your

computer/terminal, as shown below. Tighten the two screws to secure
the connector to the port.

4. Plug the power pack into a power source.
5. Once the scanner has been fully connected, power up the

terminal/computer.

Summary of Contents for IMAGETEAM 3800





































































































































Search results

Summary of Contents for IMAGETEAM 3800

Reviews:

Related manuals for IMAGETEAM 3800

Brands by name

Popular brands

Welch Allyn IMAGETEAM 3800, User Manual

Search results

Summary of Contents for IMAGETEAM 3800

Reviews:

Related manuals for IMAGETEAM 3800

Brands by name

Popular brands