Weil-McLain UO-3 CV Instruction Manual Download Page 4

4

General Information

Section: General Information

Hazard Defi nitions 

Within the boundaries of the hazard warning, there will 
be information presented describing consequences if the 
warning is not heeded and instructions on how to avoid 
the hazard. 

Indicates a hazardous situation, 
which, if not avoided, will result 

in death or serious injury.

Indicates a hazardous situation, 
which, if not avoided, could 

result in death or serious injury.

Indicates a hazardous situation, 
which, if not avoided, could 

result in minor or moderate injury. 

Intended to bring special attention 
to information, but not related to 

personal injury or property damage.

Owner’s Responsibility

Incorrect installation, adjustment, and 

use of this burner could result in severe 

personal injury, death, or substantial 

property damage from fi re, carbon 

monoxide poisoning, soot or explosion.

Contact a professional, quali

fi

 ed service agency for the 

installation, adjustment and service of your oil heating 

system.  This work requires technical training, trade 

experience, licensing or certi

fi

 cation in some states and 

the proper use of special combustion test instruments. 

Please carefully read and comply with the following 

instructions: 

Never store or use gasoline or other 

fl

 ammable 

liquids or vapors near this burner or appliance. 
Never attempt to burn garbage or refuse in this 
appliance.
Never attempt to light the burner/appliance by 
throwing burning material into the appliance. 
Never attempt to burn any fuel not speci

fi

 ed and 

approved for use in this burner.
Never restrict the air inlet openings to the burner or 
the combustion air ventilation openings in the room.

y

y

y

y

y

Please read and understand the manual supplied with 

this equipment. This equipment must be installed, 

adjusted and put into operation only by a quali

fi

 ed 

individual or service agency that is:

Licensed or certi

fi

 ed to install and provide technical 

service to oil heating systems.
Experienced with all applicable codes, standards 
and ordinances.
Responsible for the correct installation and 
commission of this equipment.
Skilled in the adjustment of oil burners using 
combustion test instruments.

The installation must strictly comply with all applicable 

codes, authorities having jurisdiction and the latest 

revision of the National Fire Protection Association 

Standard for the installation of Oil-burning Equipment, 

NFPA 31 (or CSA-B139 and CSA-B140 in Canada).

Regulation by these authorities take precedence over the 

general instructions provided in this installation manual.

y

y

y

y

Incorrect installation, adjustment, and 

use of this burner could result in severe 

personal injury, death, or substantial 

property damage from fi re, carbon 

monoxide poisoning, soot or explosion.

Professional Service   
Required

Frozen Plumbing and 
Water Damage Hazard

If the residence is unattended in severely cold weather, 

burner primary control safety lockout, heating system 

component failures, power outages or other electrical 

system failures could result in frozen plumbing and 

water damage in a matter of hours. For protection, take 

preventive actions such as having a security system 

installed that operates during power outages, senses low 

temperature and initiates an effective action. Consult with 

your heating contractor or a home security agency. 

Summary of Contents for UO-3 CV

























Reviews: