Weco WF-107, Instruction Manual, Page: 3 / 32

WF-107
Cod.006.0001.1260
10/07/2017 v2.14
ENGLISH
0
1 INTRODUCTION ................................................................. 4
2 FRONT PANEL ................................................................... 4
3 REAR PANEL ..................................................................... 4
4 INSTALLATION .................................................................. 5
4.1 WIRE SPOOL POSITIONING .............................................. 6
4.2 POSITIONING THE WIRE IN THE WIRE FEEDER .............. 6
5 USER INTERFACE ............................................................. 8
6 UNIT POWER-UP................................................................ 9
6.1 SOFTWARE COMPATIBILITY BETWEEN THE DEVICES ... 9
7 RESET (LOAD FACTORY SETTINGS) ............................. 10
7.1 TOTAL RESET .................................................................. 10
7.2 PARTIAL RESET ............................................................... 10
8 SET-UP (INITIAL SET-UP OF THE WELDING POWER
SOURCE).......................................................................... 11
COOLER ACTIVATION ................................................................ 11
REMOTE CONTROLLER SELECTION ......................................... 11
ADJUSTMENTS BLOCK SELECTION .......................................... 11
PUSH PULL ................................................................................. 11
SELECTION OF BURN TYPE....................................................... 11
8.1 LOCKING PROCEDURE ................................................... 12
Enabling ....................................................................................... 12
Disabling ...................................................................................... 12
8.2 TORCH LOADING ............................................................. 13
9 ALARMS MANAGEMENT ................................................. 13
AL. HEA. ...................................................................................... 13
AL. COO. ..................................................................................... 13
Err. C0 ......................................................................................... 13
Err. C1 ......................................................................................... 13
Err. C2 ......................................................................................... 13
Err. C4 ......................................................................................... 13
Err. C11 ....................................................................................... 13
Err. C12 ....................................................................................... 13
Err. C69 ....................................................................................... 13
AL. Cur......................................................................................... 14
AL. Mot. ....................................................................................... 14
10 WELDING PARAMETERS ................................................ 15
10.1 PARAMETERS ACTIVATION ............................................ 16
Working voltage ............................................................................ 16
Welding inductance ...................................................................... 16
Wire feed rate ............................................................................... 16
Welding current ............................................................................ 16
Thickness ..................................................................................... 16
Programs ..................................................................................... 16
Time On ....................................................................................... 16
Time Off ....................................................................................... 16
Hot Start ....................................................................................... 16
Crater Filler .................................................................................. 16
3 Levels Slope .............................................................................. 16
Soft Start ...................................................................................... 16
Motor Slope .................................................................................. 16
Bourn Back .................................................................................. 16
Post gas time ............................................................................... 16
Pre gas time ................................................................................. 16
11 WELDING SETTINGS ....................................................... 17
11.1 MIG/MAG WELDING ......................................................... 17
11.1.1 SETTING MIG/MAG PARAMETERS (MAIN WELDING
PARAMETERS) ........................................................................... 17
11.1.2 MIG/MAG PARAMETERS SETTING (2ND LEVEL) ....................... 18
11.1.3 MIG/MAG PARAMETERS SETTING (GAS MENU) ....................... 18
12 JOBS MANAGEMENT ...................................................... 19
12.1 SAVING A JOB.................................................................. 19
12.2 LOADING A USER JOB OF FACTORY SET JOB .............. 19
12.3 DELETING A JOB ............................................................. 19
13 TORCH TRIGGER MODES ............................................... 20
13.1 2T MIG/MAG WELDING .................................................... 20
13.2 4T MIG/MAG WELDING .................................................... 20
13.3 3 LEVEL MIG/MAG WELDING ........................................... 20
14 TECHNICAL DATA ........................................................... 21
15 SPARE PARTS.................................................................. 22
15.1 WF-107 .............................................................................. 22
15.2 WIRE FEEDER MOTOR .................................................... 24
15.3 WIRE FEEDER ROLLS ...................................................... 26
15.3.1 STANDARD ................................................................................. 26
15.3.1 DOUBLE DRIVE ........................................................................... 26
16 ELECTRICAL DIAGRAM ................................................... 27
16.1 WF-107 .............................................................................. 27
16.2 CAVO 320 MSR→WF-107 ................................................. 28
16.3 REMOTE CONTROLLER ................................................... 29
16.3.1 RC03: ELECTRICAL DIAGRAM.................................................... 29
16.3.2 RC04: ELECTRICAL DIAGRAM.................................................... 29
16.3.3 RC05: ELECTRICAL DIAGRAM.................................................... 30
16.3.4 RC06: ELECTRICAL DIAGRAM.................................................... 30
16.4 PUSH PULL (OPTIONAL) .................................................. 30