background image

Transport, packaging and storage 

 

72800153 Markoprint XB4JET / XB8JET 

 

Seite 29 von 162 

GB 

Symbols on packaging 

 

 

This way up 

The  arrowheads  indicate  the  top  of  the  package.  They  must 
always face upward to avoid damage to the content. 

 

Fragile 

Identifies packages with fragile or sensitive contents. 

Handle  the  package  with  care,  do  not  drop  or  subject  to 
impacts. 

 

Keep dry 

Keep packages away from moisture and keep dry. 

 

Protect from heat 

Protect packages from heat and direct sunlight. 

 
 

Transport inspection 

 

Check the delivery for completeness and transport damages immediately upon receipt. 
Proceed as follows in case of externally visible transport damage: 

  Decline delivery or accept with reservation only. 

  Record extent of damage in the transport documentation or on the delivery note 

of the haulier. 

  Initiate complaint. 

 

Complain  about  each  defect  as  soon  as  it  is  detected.  Claims  for  damages  can 
only be made within the applicable claim periods. 

 

Summary of Contents for Markoprint XB4JET



































































































































































Reviews: