45
45
BATTERY
REMOVAL
ANGEL™ 4
BATTERY REMOVAL
The battery is a metal hydride 4.8 volt stick and is an item that will wear out with time
dependant on the number of charges / discharges it has completed. An indication of
a worn battery is that it will not charge fully or that it will not hold a charge for a
prolonged period. To replace the battery, follow the procedure below.
· Remove the grip cheek cover by removing the 6 retaining screws using a metric
2.5mm A/F Allen key.
· Unplug the battery and solenoid plugs from the PCB
.
· Remove the 2 grip frame screws,
holding the frame to the body using a suitable
3mm A/F Allen key.
· Remove the grip frame
from the body.
· Ensure the SENSI™ rod
is not lost.
· Remove the breech block pull knob
by gently pulling and unscrewing counter-
clockwise.
· Remove the countersunk screws
holding the back plate in place using a suitable
2.0mm A/F metric Allen key.
· Carefully lift the back plate
off.
· Retract breech block spring
and lock pin
.
· Carefully feed the battery plug
and the solenoid plug
that was inserted into
the PCB though the ANGEL™ body and withdraw the wires from the rear of the
ANGEL™
· Remove the battery spacer
from the battery cavity.
· Carefully withdraw the metal hydride battery
from the ANGEL™ body.
· Re-assemble in reverse order.
IMPORTANT NOTES: For re-assembly of components
· Do not pull or apply excessive force to the wires.
· Do not trap any wiring or damage will occur to the wiring resulting in a fault
developing.
· Do not attempt to disassemble the battery stick.
· Ensure that when the switch is replaced that it is rotated so that the
ON
position is as per the diagram in the section SWITCHING ON YOUR
ANGEL™ - page 4.
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
MAINTENANCE –
BATTERY REMOVAL
• Ensure a barrel blocking device is fitted to the ANGEL™
• Ensure the hopper is removed from the ANGEL™
• Ensure that there are no paintballs in the ANGEL™
• Always remove the first stage regulator and relieve all residual gas pressure
from the ANGEL™ before disassembly.
• The ANGEL™ can hold a small residual charge of gas, typically 2 shots, with the
first stage regulator removed. Always discharge the marker in a safe direction to
relieve this residual gas pressure.
m
WARNING
ADHERE STRICTLY TO THESE
AND ALL OTHER SAFETY
INSTRUCTIONS AND GUIDELINES
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
