manualshive.com logo in svg

Wavetek 3HRV, Operation Manual

Share
Download
Wavetek 3HRV Operation Manual Download Page 87

4-64

Results File

Enter a file name for the Auto Test results to be stored. If an existing
file name is used, a warning message will appear prompting the user
to overwrite the existing file or create a new one. When the desired
file name has been entered, press the 

OK

 soft key to proceed with

the Auto Test.

Type Of Test

Press the 

Immediate

 soft key to commence the Auto Test. Press the

Scheduled

 soft key to perform the Auto Test repeatedly at scheduled

intervals.

Immediate

If the Immediate mode is selected the unit will commence the Auto
Test sequence. Prior to starting the test, the unit will prompt you to
enter the ambient temperature. The temperature displayed is the
temperature sensed by the unit. Use the numeric entry keys to enter
the ambient temperature. Press the 

OK

 soft key when the desired

temperature has been entered.  While the Auto Test is in progress,
the following screen is displayed:

Summary of Contents for 3HRV









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands