manualshive.com logo in svg

Wavetek 3HRV, Operation Manual

Share
Download
Wavetek 3HRV Operation Manual Download Page 47

4-24

Channel Number

The channel number of the carrier. Enter channel number by using
the numeric entry keys or the arrow keys.

Label

The label is provided to associate a channel's number with it's
programming. Using the alpha keys, label the channel with a desired
name (up to four characters). "Special" characters can be selected
using the up/down arrow keys. The label will appear to the left of the
channel number on most screens.

Sweep Channel

Y/N - Designates that the channel will be used for Sweep
measurements.

NOTE: Adding sweep points at increments other than 250 kHz will

slow the sweep speed by 15 msecs per non-250 kHz
increment.

Measurement Bandwidth Adjustments

To edit the bandwidth, cursor to the 

Measurement BW

 selection.

The bandwidth can be adjusted by using the 

UP

 and 

DOWN

 arrow

keys or by entering a value using the numeric keypad and then
pressing the 

ENTER

 key. The FCC specification for C/N measure-

ments is a bandwidth of 4.200 MHz. CATV organizations outside of
the United States may have different requirements.

Noise Offset Frequency Adjustments

The frequency at which the noise level is measured is the Carrier
frequency plus the noise offset. To adjust the noise offset, cursor to
the 

Noise Offset

 selection. The offset can be adjusted by using the

UP

 and 

DOWN

 arrow keys or by entering a value using the numeric

keypad and then pressing the 

ENTER

 key.

Summary of Contents for 3HRV









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands