manualshive.com logo in svg

Wavetek 3HRV, Operation Manual

Share
Download
Wavetek 3HRV Operation Manual Download Page 3

Contents

SECTION 1 - GENERAL INFORMATION

1.1 INTRODUCTION ................................................................ 1-1

1.2 SPECIFICATIONS ............................................................. 1-2

1.2.1 Frequency .................................................................... 1-2
1.2.2 Level Measurement ................................................... 1-2
1.2.3 Hum Measurement ..................................................... 1-3
1.2.4 Carrier to Noise Measurement .................................. 1-3
1.2.5 Telemetry .................................................................... 1-4
1.2.6 Transmitter .................................................................. 1-4
1.2.7 Spectrum Mode ........................................................... 1-4
1.2.8 Intermodulation Distortion ........................................ 1-5
1.2.9 Depth of Modulation .................................................. 1-5
1.2.10 Serial Interface .......................................................... 1-5
1.2.11 General ....................................................................... 1-5
1.2.12 Powering .................................................................... 1-6
1.2.13 Standard Accessories ................................................. 1-6
1.2.14 Options ....................................................................... 1-6
1.2.15 Optional Accessories ................................................. 1-6

SECTION 2 - INSTALLATION

2.1 INTRODUCTION ............................................................... 2-1

2.2 UNPACKING AND INSPECTION ................................... 2-1

2.3 INSTALLATION .................................................................. 2-1

2.4 WARRANTY INFORMATION .......................................... 2-2

2.5 POWER REQUIREMENTS ............................................... 2-3

2.6 CABLE SPECIFICATIONS ................................................ 2-3

2.7 TECHNICAL SUPPORT .................................................... 2-5

Summary of Contents for 3HRV









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands