manualshive.com logo in svg

Wavetek 3HRV, Operation Manual

Share
Download
Wavetek 3HRV Operation Manual Download Page 102

B-5

cancel.

Message

SORRY... The active plan cannot be deleted!

Condition

An attempt to delete the active
channel plan.

Response

Select a different plan as the active
plan, then delete the desired plan.

Message

ERROR... This plan is corrupted and cannot be

used!

Condition

The plan cannot be used because

of

a non-volatile memory

failure.

Response

Delete the plan and then choose
another.

Message

WARNING... A plan with this name already exists.

Overwrite?

Condition

A channel plan with the same name
currently exists.

Response

Overwrite or choose another name.

Message

SORRY...This is the name of a fixed plan and

cannot be used.

Condition

An attempt was made to name a
channel plan with the name of a
fixed plan.

Response

Choose another name.

Message

ERROR... The stop frequency has been set too low.

Condition

The stop frequency has been set
below the lowest channel in the
selected fixed plan.

Response

Enter a higher stop frequency.

Message

SORRY... This cannot be completed due to a system

error.

Condition

A system error was detected.

Response

Restart the unit and try again.

Message

WARNING... This channel will be deleted!

Condition

A channel is about to be deleted.

Summary of Contents for 3HRV









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands