Wavecom WMO2 Manual Download Page 76

Page: 76 / 96

WMO2 G900 / G1800 / G1900

WCOM/GSM/WMO2/WMO2ATDOC

Friday 21 May 1999

WAVECOM confidential ©

4.9.2

DTE-DCE character fICF

This command is used to determine the local serial port start-stop

(asynchronous) character framing that the DCE shall use.

Command syntax:

AT+ICF= <format>, <parity>

* <format>:

Autodetect

not supported

8 Data 2 Stop

supported

8 Data 1 Parity 1 Stop

supported

8 Data 1 Stop

supported

7 Data 2 Stop

supported

7 Data 1 Parity 1 Stop

supported

7 Data 1 Stop

supported

* <parity>:

Odd

supported

Even

supported

Mark

supported

Space

supported

None

supported

Note 1) setting a character framing different from 8N1 will disable

autobauding (in the case it was activated). However setting it back to 8N1

will not re-enable autobaud.

Note 2) setting the framing to 8N1 will let the autobauding enabled, if it
was already enabled (implying framing was already 8N1).

Application to GSM

AT+ICF?

GSM to application

+ICF: 3,4

current values

Application to GSM

AT+ICF=?

GSM to application

+ICF: (1-6),(0-4)

possible values.

Application to GSM

AT+ICF=0,0

GSM to application

new values

Summary of Contents for WMO2

































































































Search results

Summary of Contents for WMO2

Reviews:

Brands by name

Popular brands

Wavecom WMO2, Manual

Search results

Summary of Contents for WMO2

Reviews:

Brands by name

Popular brands