background image

 

15

10. Place the regulator back into the brackets and secure into place 

with panel nut.

11. Reattach bracket and attached components to the back panel and 

tighten screws loosened in step 2.

12. Insert the water tubing back into the push to connect inlet fitting. 
13. Turn water supply to CSM instrument back on.
14.  Turn CSM instrument on and check for leaks.

9.5 Replacing the Air Pump (Kit #28164S)

To replace the air pump on the CSM instrument:

1.  Disconnect the vent tube from the side of the cabinet.
2.  Disconnect the ribbon cable from the optical board.
3.  Loosen the press to connect fitting and disconnect the drain tubing 

at the bottom of the enclosure.

4.  Loosen the optical block assembly bracket screws. This is the 

bracket that holds the optical block assembly to the back panel.

5.  Lift optical block assembly up and off of bracket screws.
6.  Pull optical block assembly forward to access the air pump. The air 

pump is located on the back right hand side.

7.  Disconnect the black and pink air pump wiring (connection located 

in the electrical panel).

8.  Unscrew black fitting from air pump.

9.  Unscrew 2 screws from underneath air pump bracket.

10. Cut the zip tie that attaches the air pump to the optical board and 

then remove air pump.

11. Insert new air pump. Be sure the arrow on the new air pump is 

facing the correct direction.

12. Install 2 screws from underneath air pump bracket.
13. Attach air pump to optical board using the included zip tie.
14. Screw in black fitting into air pump outlet.
15. Reconnect the black and pink air pump wiring (connection located 

in the electrical panel).

16. Slide the optical assembly with new air pump back to original 

position. 

17. Place optical block assembly onto bracket screws located on the 

back panel of the enclosure.

18. Tighten the optical block assembly bracket screws. 

19. Reconnect the drain tubing, ribbon cable and vent tube.

9.6 Replacing the Solenoid Valve

To replace the solenoid valve on the CSM instrument:
1.  Remove the two solenoid valve mounting screws.

2.  Unplug wiring from harness.

Disconnect 

vent tube

Disconnect 

ribbon cable

Disconnect 

drain tubing

Loosen bracket 

screws

Air pump located on 

back right side of optical 

block assembly

1

4

2

3

Unscrew 

black fitting

Unscrew air pump 

bracket screws

Cut zip tie

Be sure arrow is 

pointing in same 

direction when 

installing new air 

pump

8

10

11

9

Unplug wiring

Remove fittings

2

3

To prevent damage to the wiring, ensure wiring is routed behind bracket 
and not pinched between the bracket and the back panel of the 
enclosure.

NOTICE

1

Remove screws on 
solenoid valve

Summary of Contents for 28062

















Reviews: