Watson-Marlow 630 U Installation, Operating And Maintenance Manual Download Page 97

Page: 97 / 186

22.6

Connecting using the web browser

Now that the pump is connected to the PC, the web browser can be opened.

How does the web browser work?

The web browser is a window to view content

In the case of the internet, content is downloaded from websites using HTML

In the case of the pump, HTML is stored internally

How to use the web browser

Launch web browser (e.g. Internet Explorer®)

Type 192.168.1.12 into the address bar. The pump web page will open displaying the ‘Overview’ tab.

22.7

Connecting to a PLC

This pump is designed in accordance to the EtherNet/IP™ specification for use with any PLC system using
EtherNet/IP™.

Automatic configuration by installing the EDS File (Rockwell add on profile)

Downloading the EDS file

The EDS file is available for download from the WMFTG website.

•

Navigate to the WMFTG website.

•

Navigate to the 'Literature' page by clicking the link on the home page.

•

Type 'EDS' in the search filter and click search.

m-630un-en-08

Summary of Contents for 630 U



























































































































































































Search results

Summary of Contents for 630 U

Reviews:

Watson-Marlow 630 U, Installation, Operating And Maintenance Manual, Page: 97 / 186

Search results

Summary of Contents for 630 U

Reviews: