background image

 

WL500

 Manual 

                                                                           Page 58   Revision 4‐10‐2019 

29.

 

Once the machine reaches its target temperature, the Compressor and fan will shut off.  Draw a 
glass of cold water and verify it is has been chilled to proper temperature. 

 

Heater Test 
 

30.

 

Always ensure tanks are full of water before turning on the heater or the overload (high limit) will 
open and require manual reset.  It will take the heater approximately 10 minutes to heat the water 
from ambient 75

F to the factory set point of 189

F.  You can monitor the Hot Tank temperature by 

selecting the hot button when the Temp Display is RANGING.  Dispense a cup of hot water to ensure 
the temperature/odor/taste is acceptable. 

 

WARNING!  

VERY HOT WATER CAN BURN OR SCALD.

 

 Hot water should be dispensed carefully into insulated container to avoid injury.  

 

Drain the 

WL500

 Water Treatment System for Transport 

 

31.

 

Drain the 

WL500

 

Water Treatment System 

for transportation per the Draining Instructions in this 

manual. 
 

       WARNING!

  

STORE UNIT EMPTY.  ALWAYS SANITIZE BEFORE REUSE. 

The unit must be completely drained and sealed before storing to avoid stagnation and reduce 
microbiological contamination (potential bacterial growth).  

 

Summary of Contents for WL500 - Sparkling















Reviews: