background image

7

Step 3:

 Install the Drain Saddle

1. 

Choose a spot on the drainpipe that is convenient for installing the drain saddle 

and drill a 1/4” hole. Be sure not to penetrate the opposite side of the pipe;

     

NOTE:

 

It’s recommended to install the drain saddle on the vertical drainpipe.

2. 

Slip the front plate to one end of the tubing (without mark), and insert the tubing 

into the drilled hole up to about 3/5” (Figure 7);

3. Fix the drain saddle with screws and install the lock clip on the fitting to secure 

the connection (Figure 8);

NOTE:

 

In some areas, the “WASTE” water tubing needs to be connected to 

the drainpipe through the air gap. Consumers need to purchase additional air 

gap accessories. 

Figure 6

Figure 7

Figure 8

Front Plate

About 3/5"

5.9"

17.3"

Back Plate

Step 4: 

Position the RO System Housing

Check and ensure there is sufficient space under the countertop to install the 

system (17.3 inches 

*

 5.9 inches

*

 14.0 inches).

NOTE:

 

Make sure that there is a power outlet in the kitchen cabinet or on the wall 

connected to the lower cabinet space before installation.

It is not recommended to place the housing against the cabinet, as there may be 

vibrations when the system works.

14"

Summary of Contents for G2 Series

























Reviews: