background image

CONNECT TO WATER SUPPLY

The Installation Diagram shows an overview of the water 

supply connection including the Pressure Limiting Valve.

CONNECT DUAL FAUCET TO WATER SUPPLY (IF FILTER SYSTEM NOT INCLUDED)

•   Take blue tube from Dual Faucet and insert into the tube connector at the end of the PLVDC as shown 

in Step 7.

•   Pull back on the tube to ensure tube is locked into position.
•   Connect red locking clip where shown in Step 7.
•   Tubing must not be kinked or twisted.
•   Tubing should be cut to a convenient length but should not be stretched taut.
•   Ensure all fittings and tube connections are protected against damage from objects stored in the 

cupboard.

•   The 350kPa pressure 

limiting dual check 

valve (PLVDC) must be 

connected to the stop tap 

as shown. Use plumbing 

tape to create seal.

•   Use plumbing tape to 

connect the ¼" mbsp 

to ¼" tube pushfit 

connector to the PLVDC

Stop tap for cold water

supply (not included)

 

¼” mbsp x ¼”

tube connector

Pressure Limiting

Dual Check 

Valve 350kPa

 

Locking clip

INSTALL FILTER SYSTEM (IF INCLUDED) REFER INSTALLATION DIAGRAM

•   The filter system should be installed in a convenient location. Please allow 40mm clearance 

underneath the filter to facilitate filter replacement.

•   Locate the head assembly and affix to kitchen cupboard with screws and bracket supplied.
•   The head assembly has 'pushfit' fittings on the inlet and outlet. Remove the red locking clips.
•   Take the length of blue tubing supplied and cut to size to connect from the outlet of the filter head to 

the PLVDC. Make sure tube is cut square and clean with a Stanley knife or similar.

•   Take blue tubing from the dual faucet and insert in the outlet (right hand side of filter head) of filter 

head assembly. Push tubing in and then pull back to ensure a tight seal. Reconnect locking clip.

•  Water flow must be in the direction indicated by the arrow on the top of the filter head.
•   Insert filter cartridge into filter head - twist cartridge a quarter turn anti clockwise until cartridge 

locks firmly into filter head. 

STEP 7

STEP 8

STEP 9

Summary of Contents for K-WFADUOGN

















Reviews: