background image

Introduction

Technical specifications

The following table lists the technical specifications for the HiFi Mic:

Operating
voltage

Transmitter: 4.2 VDC

Base: 12 VDC

Frequency

900 MHz (902 – 928 MHz) – 52 channels, digital spread
spectrum

Operating
range

Over 1 mile in open line of sight

Important!

Operating

range differs according to
the environment.

Jacks

Transmitter: Lapel microphone jack

Base: 8-pin RJ-45 for power, audio out, and trigger out

Battery

Capacity: Lithium-ion 4.2 VDC/1200mAh

Charging time: 3 hours

Stand-by time: 25 days

Talk time: 8-12 hours

Note:

Performance can

degrade as the battery ages.

Warranty Information

WatchGuard Video, in recognition of its responsibility to provide quality
systems, components, and workmanship, warrants each system, part,
and component it manufactures first sold to an end user to be free from
defects in material and workmanship for a period of

one-year

from the

date of purchase. A defective component that is repaired or replaced
under this limited warranty will be covered for the remainder of the
original warranty period. Where defects in material or workmanship may
occur, the following warranty terms and conditions apply:

10

WGD00091

Revision F

Summary of Contents for hifi microphone









































Reviews: