background image

12

Single gas detector

PDM 

8. CERTIFICATES

Intrinsic Safety:

The detector is in conformity of the following standards

IECEx:        

Ex ia IIC T4 Ga

IECEx KTL 15.0018

Ex ia IIC T4 Ga

Class I, Zone 0, AEx ia IIC T4 Ga

Class I, Division 1, Groups A, B, C, D, T4

C22.2 No. 60079-0:2015; C22.2 No. 60079-11:2014;

C22.2 No. 61010-1-12:2010; UL 61010-1,

Ed. 3; UL 913, Ed. 8; UL 60079-0, Ed. 6; UL 60079-11, Ed. 6

ATEX:        

 2198 

 II 1 G Ex ia IIC T4 Ga IP67 

KRH16ATEX1048

Directive 2014/34/EU

KCS:           Ex ia IIC T4

KTL 16-KA2BO-0457

INMETRO      Ex ia IIC T4 Ga

BVC16.5919/02

Compliance: 

Electromagnetic Compatibility Directive 2014/30/EU

Standards:

The electrical apparatus and any acceptable variations to it specified in the schedule of this

certificate and the identified documents, was found to comply with the following standards:

•  IEC 60079 0: 2011 Ed. 6

•  IEC 60079 11: 2011 Ed 6

•  UL 61010 1, Ed. 3

•  UL 913, Ed. 8

•  UL 60079 0, Ed. 6

•  UL 60079 11, Ed. 6

•  C22.2 No. 60079 0:2015

•  C22.2 No. 60079 11:2014

•  C22.2 No. 61010 1 12:2012

•  EN 60079 0: 2012+A11:2013

•  EN 60079 11: 2012

Manufacturing Approval:

The detector manufacturer is certified compliant with ISO 9001:2000 provisions

Summary of Contents for PDM














Reviews: