waratah HTH624C, Operator'S Manual

Page: 84 / 87

Index
Page
C
Chain shot guard
Inspection............................................................... 1-2-8
Control valve
Fault finding ........................................................... 3-4-1
E
Electrical installation—general
Using booster batteries—TimberRite™ ................. 4-1-6
Welding on carrier or harvester—TR100 ............... 4-1-2
G
General
Avoid unauthorized machine modifications............ 0-1-2
Copyright................................................................ 0-1-1
General information ............................................... 0-1-1
I
Introduction
Features................................................................. 0-1-3
Manual replacement .............................................. 0-1-1
L
Label precautions
Do not operate warning-unless seated .................. 1-6-2
Do not stare into the laser beam............................ 1-3-2
Keep clear of saw .................................................. 1-2-4
Lock crossover bracket .......................................... 1-1-1
Pinch area.............................................................. 1-3-1
Recommendations for processing on the landing.. 1-6-1
Recommendations for tree felling .......................... 1-6-1
Welding .................................................................. 1-6-2
M
Maintenance—fluids and lubricants
Recommended hydraulic system fluid ................... 3-1-1
Maintenance—fluids and lubricants
Grease point location location—top saw unit......... 3-1-6
Maintenance—fluids and lubricants
Grease measuring wheel bearings ........................ 3-1-6
Maintenance—fluids and lubricants
Grease point location—main saw unit
(3/4” saw option) .................................................. 3-1-7
Maintenance—fluids and lubricants
Grease ................................................................... 3-1-2
Maintenance—fluids and lubricants
Grease point location—upper delimb knife ............ 3-1-3
Maintenance—fluids and lubricants
Grease point location—feed arm ........................... 3-1-4
Maintenance—fluids and lubricants
Grease point location—tilt bracket ......................... 3-1-5
Page
Maintenance—fluids and lubricants
Grease point location—length measuring unit ....... 3-1-5
Maintenance—fluids and lubricants
Grease point location ............................................. 3-1-3
Maintenance—fluids and lubricants
Grease point location—main saw unit
(SC100 option) ..................................................... 3-1-7
Maintenance—fluids and lubricants
Chain oil ................................................................. 3-1-1
Maintenance—general
Additional metric cap screw torque values............. 3-3-3
Metric bolt and cap screw torque values................ 3-3-2
Unified inch bolt and cap screw torque values....... 3-3-1
Maintenance—schedule
Maintenance every 1000 hours.............................. 3-2-5
Maintenance every 2000 hours or yearly............... 3-2-6
Maintenance every 200—250 hours or monthly .... 3-2-4
Maintenance every 50 hours or weekly ................. 3-2-3
Maintenance every 8 hours or daily ....................... 3-2-2
Periodic maintenance record ................................. 3-2-1
Miscellaneous—carrier
In case of carrier fire .............................................. 4-1-1
Prevent fires........................................................... 4-1-1
Welding on carrier.................................................. 4-1-3
Welding on carrier or harvester—TR100 ............... 4-1-2
Miscellaneous—measurements
Metric and imperial unit expressions...................... 4-2-1
Miscellaneous—specification conversion
Liquid ..................................................................... 4-3-2
Miscellaneous—specification conversion
Flow ....................................................................... 4-3-2
Miscellaneous—specification conversion
Length .................................................................... 4-3-1
Miscellaneous—specification conversion
Pressure................................................................. 4-3-2
Miscellaneous—specification conversion
Volume ................................................................... 4-3-2
Miscellaneous—specification conversion
Miscellaneous ........................................................ 4-3-3
Miscellaneous—specification conversion
Weight.................................................................... 4-3-1
Miscellaneous—specification conversion
Area ....................................................................... 4-3-1
Miscellaneous—wood measurement
Wood measurement equivalents ........................... 4-4-1
O
Operation—clear cut harvesting
Delimbing ............................................................... 2-2-2
Fall and delimb....................................................... 2-2-2
Felling .................................................................... 2-2-1
Felling process....................................................... 2-2-1
Operation—cutting
General .................................................................. 2-5-1
Using the main saw unit......................................... 2-5-1
Using the top saw unit............................................ 2-5-1
Continued on next page
Index-1 053122
PN=
8 4