background image

14

W 600 Flexio 18V

EN

• 

When working with the W 600 indoors as well as outdoors ensure that no solvent 

vapors are sucked in by the spray gun.

• 

The spray gun is not a toy; children must therefore not be allowed to handle it or play 

with it.

• 

Remove the battery before carrying out any work on the spray gun.

• 

Cover areas that are 

not

 to be sprayed. When working keep in mind that wind, for 

example, may transport paint mist over great distances and cause damage.

• 

Never open the device yourself in order to carry out repairs in the electrical system!

• 

The units may only be used with a functional valve. 

If paints rises in the ventilating 

hose (Fig. 1, item 16) do not operate the unit further! 

Dismantle and clean the 

ventilating hose, valve and diaphragm and replace the diaphragm if necessary.

• 

Do not lay the spray gun.

With original WAGNER accessories and spare parts, you have the guarantee that 

all safety regulations are fulfilled. 

4. Safety instructions for the charger and battery

Only use the tool with BOSCH POWER FOR ALL compatible PBA 18V 

batteries with at least 2.5 Ah and suitable chargers. The battery voltage 

must match the battery charging voltage of the charger. Do not charge 

non-rechargeable batteries. Otherwise there is a risk of fire and explosion.

• 

Only use the charger indoors and keep it away from moisture. 

 Water penetrating 

into a power tool increases the risk of an electric shock.

• 

Keep the charger clean.

 There is a risk of electric shock due to contamination.

• 

Before every use, check the charger, cable and plug. Do not use the charger if it is 

damaged. Do not open the charger yourself and only have it repaired by qualified 

specialist personnel using original spare parts. 

Damaged chargers, cables and plugs 

increase the risk of electric shock.

• 

Do not operate the charger on easily combustible surfaces (e.g. paper, textiles, 

etc.) or in combustible environments. 

There is a risk of fire due to the heating of the 

charger during charging.

• 

The battery is delivered partially charged. 

To ensure full battery performance, fully 

charge the battery in the charger before first use.

• 

Only use the battery in the manufacturer's products.

 This is the only way to protect 

the battery from dangerous overloading. 

• 

Keep batteries out of the reach of children.

• 

Do not open the battery. There is a risk of a short circuit.

• 

Vapours may also escape if the battery is damaged or used improperly. 

Take in 

fresh air and consult a doctor if you have any symptoms. The vapours may irritate the 

respiratory tract.

• 

If the battery is defective, liquid may leak out and wet adjacent objects. 

Check 

affected parts. Clean them or replace them if necessary.

• 

The battery can be damaged by sharp objects such as nails or screwdrivers or by 

external force. 

An internal short circuit may occur and the battery may burn, smoke, 

explode or overheat.

Summary of Contents for W 600 FLEXIO 18V































Reviews: