background image

WAFER GSM-KEY-DC REMOTE CONTROL UNIT 

http://www.waferstar.com 

INSTALLATION 

To install the GSM-KEY, you need to connect the 2 wires of the relay contact in parallel with 

the gate opening button. The relay contacts can stand 

48V 0.5A maximum

, this is enough for its 

operation but 

don't try to switch higher voltages or currents

. You should install the GSM-KEY 

in a place where there is GSM signal coming from the operator you want to use. Check it with a 
phone before proceeding with the installation. If you need to install the device in a place with little 
signal, you may consider using an external antenna that we may supply as an option to be 
purchased separately with 50cm cable. 

You should then insert the SIM Card of the operator you want to use with the right direction 

as the left picure. 

!Note! : You must remove the PIN request 

from the SIM before inserting it in the

 

unit

, otherwise the device will not work. In order to 

do so, insert the SIM in a phone and 
disable the PIN request (usually there is a security 
menu that enables you to do so). 

GSM-KEY also comes with additional 2 

Input.The inputs can be used to generate alarms 
when triggered.For examples,you can can connect 
the saftey beam output to the GSM-KEY Alarm1 and 
Alarm2 input. 

WAFER GSM-KEY PROGRAMMING 

You can program the GSM-KEY with SMS commands using your phone. It is safe to do so 

because in addition to the fact that other people may not know the number of the SIM inserted in 
it, we also use a Password that makes it impossible for anybody who doesn't know it to access the 
system by chance. 

Remember that commands must be CAPITAL LETTERS. It is PWD not pwd, CAP not Cap 

etc. Don't add spaces or any other character. 

Some complicated Instructions,that cann’t be programmed by the phone SMS. That would 

need to use the PC software to program and inquire the status of the terminal. 

The bellow wire picture is to show how to connect the cable to the PC program connector 

with the Program adapter.Please connect it in the right direction with the picture. 

 

 
 
 
 
 
 
 
 

    Simple RS232 program card ( Standard )        USB program adapter box (Optional Parts) 

Summary of Contents for DC200
















Reviews: