Wacker Neuson GV 2500A Page 44 Repair Manual Download

Page: 44 / 74

Disassembly and Assembly

GV Generator Repair

wc_tx000775gb.fm

3.7

Removing the Fuel Tank

Prerequisites

Machine shut down

Procedure

Follow the procedure below to remove the fuel tank.

1. Disconnect the spark plug.

2. Close the fuel valve.

3. Disconnect the fuel hose

(a)

from fuel valve.

4. Remove the screws

(b)

that secure the tank and brace to the fuel frame and pull

the fuel tank from the frame.

5. Remove the brace from the fuel tank.

The procedure to remove the fuel tank is now complete.

3.8

Installing the Fuel Tank

Prerequisites

Machine shut down

Procedure

Follow the procedure below to install the fuel tank.

1. Install the brace to the fuel tank.

2. Position the fuel tank into the frame and secure it with screws

(b)

3. Connect the fuel hose

(a)

to the fuel valve.

The procedure to install the fuel tank is now complete.

wc_gr004397

Summary of Contents for GV 2500A











































































Search results

Summary of Contents for GV 2500A

Reviews:

Related manuals for GV 2500A

Brands by name

Popular brands

Wacker Neuson GV 2500A, Repair Manual

Search results

Summary of Contents for GV 2500A

Reviews:

Related manuals for GV 2500A

Brands by name

Popular brands