background image

20

Maintenance

It is important to keep the device clean. Clean the contact points regularly, avoid using any detergent 

that contains strong chemicals. To clean your VOSS.miniPET use a soft damp cloth using only water 

and neutral detergent. The transmitter is not waterproof, so use caution when operating your device in 

wet conditions, water can cause irreversible damage to your transmitter. The receiver is waterproof. The 

receiver case is provided with a seal that forms a waterproof barrier between the lid and main housing 

of the case. If the seal is loose, out of alignment or twisted, it will compromise the waterproof integrity of 

the case. Lubricating the seal with a thin layer of silicone grease will increase its lifespan. We recommend 

replacing the seal in the receiver every year. It is recommended to remove the battery from the receiver, 

if the device will not be in use for a month or longer.

TIP

While using the device, it is recommended to check periodically that screws in the receiver 

lid are tightened correctly.

Troubleshooting

• 

If your device seems to operate improperly, read this manual again, check the receiver battery 

and replace it if necessary.

• 

Try to initialize the receiver by removing the battery from the battery holder in the receiver, 

then use a metal tool (e.g. a screwdriver, scissors, etc. 

and short-circuit both contacts of battery holder by 

touching both poles with the metal tool at the same 

time for approximately two seconds, and then put 

the battery back in its place observing the correct 

polarity. 

A beep sound is emitted indicating the correct 

installation of the battery.

• 

If the problem still persists, try to program the trans-

mitter with receiver again according to the instruc-

tions in this manual.

If the problem still persists, contact the dealer. 

Summary of Contents for VOSS.miniPet

























Reviews: