06 Starting and driving
Alcoguard*
06
150
*
Option/accessory, for more information, see Introduction.
Bypass function will then be possible, see
page 150 section Emergency situation.
The message can be cleared by pressing the
send button (3) once. Otherwise it goes out on
its own after approx. 2 minutes but then reap-
pears each time the engine is started - only
recalibration at a workshop
1
can clear the mes-
sage permanently.
Cold or hot weather
The colder the weather the longer it takes
before the Alcolock is ready for use:
Temperature (ºC)
Maximum heat-
ing time (sec-
onds)
+10 — +85
10
–5 — +10
60
–40 — –5
180
At temperatures below -20 ºC or above
+60 ºC the Alcolock requires additional power
supply. The display shows
ALCOGUARD
INSERT POWER CABLE
. In which case, con-
nect the power supply cable from the glovebox
and wait until indicator lamp (6) is green.
In extremely cold weather the heating time can
be reduced by taking the Alcolock indoors.
Emergency situation
In the event of an emergency situation, or if the
Alcolock is out of order or has been removed,
it is possible to bypass the Alcolock in order to
drive the car.
NOTE
All Bypass activation is logged and saved in
memory, see page 12 in the section,
Recording data.
After the Bypass function has been activated
the display shows
ALCOGUARD BYPASS
ENABLED
the whole time while driving and
can only be reset by a workshop
1
.
The Bypass function can be tested without the
error message being logged - in which case,
carry out all the steps without starting the car.
The error message is cleared when the car is
locked.
When the Alcolock is installed, either the
Bypass or Emergency function is selected as
the bypassing option. This setting can be
changed afterwards at a workshop
1
.
Activating the Bypass function
•
Depress and hold the left-hand stalk
switch
READ
button and the button for
hazard warning flashers simultaneously for
approx. 5 seconds - the display first shows
BYPASS ACTIVATED WAIT 1 MINUTE
and then
ALCOGUARD BYPASS
ENABLED
- after which the engine can be
started.
This function can be activated several times.
The error message shown during driving can
only be cleared at a workshop
1
.
Activating the Emergency function
•
Depress and hold the left-hand stalk
switch
READ
button and the button for
hazard warning flashers simultaneously for
approx. 5 seconds - the display shows
ALCOGUARD BYPASS ENABLED
and
the engine can be started.
This function can be used once, after which a
reset must be made at a workshop
1
.
1
An authorised Volvo workshop is recommended.
Summary of Contents for S40 - ANNEXE 244
