manualshive.com logo in svg

Volvo D11 series, Installation Manual

The Volvo D11 series Installation Manual is a comprehensive user guide for the renowned Volvo D11 series engine. This manual provides step-by-step instructions, ensuring hassle-free installation. Download the manual for free from our website, manualshive.com, to access all the invaluable information needed to install and operate this exceptional product.

Share
Download
background image

Electrochemical corrosion

64

Shore power and  

battery charging

When shore power is connected (20V–230V), the 
shore safety ground (earth) must not be connected 
to the engine or any other ground point on the boat. 
The safety ground must always be connected to the 
connection cabinet's ground (earth) terminal ashore. 
The safety ground should not be connected to the 
negative connection on the output side (2/24V), i.e. 
it must be galvanically separated.

  WARNING! Installation and work using shore  

connected equipment may only be carried out 
by an electrician who is qualified to work on 
mains voltage installations. Incorrect installation 
can result in danger to life.

Taking into account considerations of personnel safe-
ty and care of the equipment, Volvo Penta gives the 
following recommendations regarding shore power 
alternating current (AC) installations:
Installations should be made according to figure  
or figure 2. Figure  shows a single-phase installa-
tion for either 230VAC or 20VAC. Figure 2 shows a 
230VAC input, 20/230VAC output installation. 
Figures  and 2 are based on ABYC E- diagrams 
8 and  but require a ground fault circuit interrupter 
and an isolation transformer. Figures  and 2 are 
considered best practice and are in harmonywith 
recommendations from ABYC and ISO, and provide 
protection against electrochemical corrosion and 
electrical shock.
The safety related components are important for the 
following reasons:

Isolation transformer
The isolation transformer galvanically separates the 
shore power from the boat. This minimizes the risk of 
galvanic and stray current corrosion.

Ground Fault Circuit Interrupter (GFCI)
Arcing faults between a live conductor and ground 
can be  sustained at relatively low current levels and 
does not trigger circuit breakers. Furthermore, even 
very low current levels represent danger to person-
nel. A GFCI must be installed on the secondary side 
of the isolation transformer as a ground fault protec-
tion in the boat. The GFCI trip sensitivity and trip time 
must comply with local standards.
The GFCI placed on the secondary of the isolation 
transformer ensures ground fault protection on the 
boat. This is an addition to ABYC E-, that ensures 
a higher degree of protection against electrical shock.

Ground plate
To ensure safety of personnel, a common ground 
plate below the waterline must be connected to the 
AC and DC electrical system.

Summary of Contents for D11 series





















































































































































































































Reviews:

No comments

Related manuals for D11 series

Kohler Command Pro CH940-CH1000 Owner'S Manual preview
Command Pro CH940-CH1000
Brand: Kohler Pages: 16
Kubota GR1600EU Workshop Manual preview
GR1600EU
Brand: Kubota Pages: 285
MSW MSW-GE70 User Manual preview
MSW-GE70
Brand: MSW Pages: 159
Lenze MQA Mounting And Switch-On Instructions preview
MQA
Brand: Lenze Pages: 36
Bosch DHG6015NUC Installation Manual preview
DHG6015NUC
Brand: Bosch Pages: 20
Bosch Rexroth Hagglunds CA 10 Installation And Maintenance Manual preview
Rexroth Hagglunds CA 10
Brand: Bosch Pages: 53
Bosch MKE098 Operating Manual preview
MKE098
Brand: Bosch Pages: 60
Bosch Rexroth MKE Operating Manual preview
Rexroth MKE
Brand: Bosch Pages: 74
Bosch Rexroth Hagglunds CA 100 Installation & Maintenance Manual preview
Rexroth Hagglunds CA 100
Brand: Bosch Pages: 76
Bosch Rexroth 70 Series Instruction Manual preview
Rexroth 70 Series
Brand: Bosch Pages: 56
Bosch Rexroth IndraDyn T Instructions Manual preview
Rexroth IndraDyn T
Brand: Bosch Pages: 76
Bosch Rexroth A10VER 52 Series Instruction Manual preview
Rexroth A10VER 52 Series
Brand: Bosch Pages: 56
Bosch HBL 44 Series Use And Care Manual preview
HBL 44 Series
Brand: Bosch Pages: 48
Bosch Rexroth MAD Operating Instructions Manual preview
Rexroth MAD
Brand: Bosch Pages: 114
Bosch Rexroth MAD100 Operating Instructions Manual preview
Rexroth MAD100
Brand: Bosch Pages: 72
Bosch Rexroth A6VM series 71 Manual preview
Rexroth A6VM series 71
Brand: Bosch Pages: 76
Bosch Rexroth Hagglunds VI 44 Series Installation And Maintenance Manual preview
Rexroth Hagglunds VI 44 Series
Brand: Bosch Pages: 68
Bosch Rexroth IndraDyn S MS2N Operating Instructions Manual preview
Rexroth IndraDyn S MS2N
Brand: Bosch Pages: 118

Brands by name

Popular brands

Load more brands