manualshive.com logo in svg

Volvo Penta TAD570VE, Operator'S Manual

Share
Download
Volvo Penta TAD570VE Operator'S Manual Download Page 36

Starting

Make it a habit of giving the engine and engine room a visual check before starting. This will help you to discover
quickly if anything abnormal has happened, or is about to happen.
Also check that instruments and warning displays show normal values after you have started the engine.

 WARNING!

Never use start spray or similar agents to start an engine. This may cause an explosion in the inlet manifold. Risk
of personal injury.

Before Starting

•

Check that the oil level is between the MIN and MAX
marks. Refer to 

Oil level, checking and topping up

.

•

Check the fuel pre-filter; refer to 

Draining

condensate, fuel system, page 61

.

•

Check that no leakage of oil, fuel or coolant is
present.

•

Check the coolant level and that the radiator is not
blocked externally. Refer to 

Coolant Level,

Checking and Topping Up, page 66

 and 

Charge

Air Cooler, External Cleaning, page 68

.

 WARNING!

Do not open the coolant filler cap when the engine
is hot, except in emergencies as this could cause
serious personal injury. Steam or hot fluid could
spray out.

•

Turn the main switch on.

IMPORTANT:

Never break the circuit with the main switch while
the engine is running.
Alternator and electronics could be damaged.

•

Move the engine speed control to idle, and open the
disengageable clutch/gearbox if installed.

 

34

47711083 09-2018 © AB VOLVO PENTA

Summary of Contents for TAD570VE

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands