manualshive.com logo in svg

Volvo Penta TAD570VE, Operator'S Manual

Share
Download
Volvo Penta TAD570VE Operator'S Manual Download Page 30

the solution to come into contact with other chemicals
or be mixed with other chemicals.

When handling AdBlue

®

/DEF it is important that

electrical connectors are connected or well-
encapsulated. The solution is corrosive toward certain
metals such as copper and aluminum. Should
oxidation occur, it cannot be removed.
If connectors come into contact with the solution they
must be replaced immediately to prevent the solution
from seeping further along the copper wiring.

If the solution is spilled onto the engine, wipe it away
and flush with water. White crystals of concentrated
AdBlue

®

/DEF may form in the event of a spill; wash the

crystals away using water.

IMPORTANT:

AdBlue®/DEF spillages may not be washed into
drains.
If a spill should occur, the solution must be absorbed
using dry sand or other non-flammable material and
handled according to local and national regulations.

Presentation

28

47711083 09-2018 © AB VOLVO PENTA

Summary of Contents for TAD570VE

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands