manualshive.com logo in svg

Volvo Penta TAD570VE, Operator'S Manual

Share
Download
Volvo Penta TAD570VE Operator'S Manual Download Page 62

Engine Oil, Change

 WARNING!

Hot oil and hot surfaces can cause burns.

NOTICE!

 Always follow the recommended oil change

interval and always change the oil filter in connection
with oil changes. Refer to 

Oil Grade and Oil Change

Interval

.

1 Run the engine until warm.

2 Remove the drain plug. Drain the oil.

NOTICE!

 Collect the old oil and old filters and hand

them to a re-cycling station.

3 Install the drain plug with a new gasket.

4 Change the oil filter, refer to 

Oil Filter,

Replace, page 58

.

5 Fill oil to the correct level, refer to 

Oil level, checking

and topping up, page 58

.

IMPORTANT:

Do not fill above the MAX level.

6 Start the engine and let it idle. Check that the oil

pressure is normal.

7 Stop the engine. Check that there is no oil leakage

around the filters. Check the oil level and top up with
oil as necessary. Refer to 

Oil level, checking and

topping up, page 58

.

 

Maintenance

60

47711083 09-2018 © AB VOLVO PENTA

Summary of Contents for TAD570VE

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands