manualshive.com logo in svg

Volvo Penta TAD570VE, Operator'S Manual

Share
Download
Volvo Penta TAD570VE Operator'S Manual Download Page 42

Auxiliary Stop

For location of the extra stop, refer to

Maintenance, page 54

.

 WARNING!

Working with or approaching a running engine is a
safety risk. Watch out for rotating components and hot
surfaces.

After Engine Shutdown

1 Check the engine and engine compartment for

leaks.

2 Turn off the main switches before any long

stoppage.

3 Carry out maintenance in accordance with the

schedule.

For longer breaks in operation

During longer breaks in operation, it is recommended
that the engine is warmed up at least once every two
weeks. This prevents corrosion in the engine.
If you expect the engine to be unused for two months
or more, it should be conserved. Refer to

Storage, page 80

 .

IMPORTANT:

If there is a risk of freezing, the coolant in the cooling
system must have adequate antifreeze protection.

Refer to 

Maintenance, page 65

.

IMPORTANT:

A poorly charged battery can freeze and burst.

Refer to 

Battery, Charging

.

 

 

Engine Shutdown

40

47711083 09-2018 © AB VOLVO PENTA

Summary of Contents for TAD570VE

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands