manualshive.com logo in svg

Volvo Penta TAD570VE, Operator'S Manual

Share
Download
Volvo Penta TAD570VE Operator'S Manual Download Page 70

Coolant, Draining

 WARNING!

Do not open the coolant filler cap when the engine is
hot, except in emergencies as this could cause serious
personal injury. Steam or hot fluid could spray out.

IMPORTANT:

The coolant contains corrosion-inhibiting additives.
Never drain the engine cooling system on engines,
which are to be put in storage.

1 Stop the engine.

2 Remove the filler cap (1). Do not open the pressure

cap.

3 Open all drain points. Drain the coolant from the

radiator and engine block, using the drain hose.
The drain nipples are situated under the radiator on
the right side of the engine block.

4 Check that all coolant drains out. Deposits may be

found inside the drain plug/tap, and need to be
cleared away. There is otherwise a risk that coolant
could remain and cause damage due to freezing.
Check whether the installation has any further taps
or plugs at the lowest points of the cooling water
pipes.

5 Shut any taps and check that the spring-loaded

covers on the nipples close completely. Install the
rubber plugs.

Charge Air Cooler, External
Cleaning

NOTICE!

 Regular inspect the charge air cooler

visually.

1 Cover the engine before cleaning. The charged air

cooler must be cold.

2 Clean with high pressure wash or compressed air.

Be careful not to damage the radiator fins.
If detergent is used, make sure that it is not
corrosive to aluminum.

 

 

Maintenance

68

47711083 09-2018 © AB VOLVO PENTA

Summary of Contents for TAD570VE

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands