Volvo Penta TAD1340VE Operator'S Manual Download | Manualshive

Page: 68 / 106

background image

Charge Air Pipe, Leakage Check

Inspect the condition of the charge air hoses, hose
unions and clamps for cracks and other damage.
Change as necessary.

Clamps must be tightened using a torque wrench to
9 ±2 Nm (6.6 ±1.5 lbf.ft.).

Drive Belt and Alternator Belt,
Inspection

WARNING!

Working with or approaching a running engine is a
safety risk. Watch out for rotating components and hot
surfaces.

IMPORTANT:

Always change a belt which looks worn or cracked.

Inspections must be carried out after operations, while
the belts are hot.
You should be able to depress the alternator belt and
the drive belt about 3-4 mm between the pulleys.
The alternator belts and drive belts have automatic belt
tensioners and do not need to be adjusted.
Check the condition of the drive belts. Replace as
necessary; refer to

Alternator Belt, Replace, page 68

Drive belt, change, page 67

.

P0002083

Maintenance

66

47711296 01-2019 © AB VOLVO PENTA

«
...
66
67
68
69
70
...
»

Summary of Contents for TAD1340VE











































































































Reviews:

No comments

Related manuals for TAD1340VE

Brand: Jabiru Pages: 116

Brand: Nanni Pages: 24

Brand: Daedong Pages: 66

Brand: York Pages: 40

Brand: Mercury Pages: 878

Brand: Siemens Pages: 28

6FB1203-5AT00-7MP0

Brand: Siemens Pages: 7

COMBIMASTER CM110/3

Brand: Siemens Pages: 21

Brand: Siemens Pages: 19

Brand: Siemens Pages: 24

Brand: Siemens Pages: 15

Brand: Siemens Pages: 16

Brand: Siemens Pages: 38

Brand: Siemens Pages: 24

Brand: Siemens Pages: 36

Brand: Siemens Pages: 40

Brand: Siemens Pages: 16

Brand: Siemens Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands