manualshive.com logo in svg

Volvo Penta TAD1340VE, Operator'S Manual

Share
Download
Volvo Penta TAD1340VE Operator'S Manual Download Page 28

Customer parameter / Gen set

•

Primary engine speed

 - selection of engine rpm,

1500 or 1800 rpm.

•

Preheat on ignition 

- activation of automatic pre-

heating. The engine control system senses if pre-
heating is needed and activates it directly at switch-
on.

•

Governor droop (%) 

- setting of droop level, when

activated. For activation, refer to “Governor droop”
in the main menu.

•

Overspeed limit (%)

 - setting of limit for overspeed

alarm, % of set engine rpm.

•

Overspeed shutdown

 - activation of engine shut-

down with overspeed alarm. Refer to “Overspeed
limit” to activate the alarm limit for the excess rpm
alarm.

•

Oil temp warning limit (°C)

 - setting alarm limit for

oil temperature.

•

Coolant temp limit (°C)

 - setting alarm limit for

coolant temperature.

Throttle input setting

rpm control setting (throttle operation).

•

Set throttle mode

 - OFF - engine rpm is controlled

via the DCU panel.
ext throttle input - engine speed is controlled with a
potentiometer (accelerator).
ext voltage input - engine rpm is controlled by an
external unit.

•

Set idle voltage (V)

 - idle voltage level setting.

•

Set max voltage (V)

 - full throttle voltage level

setting.

 

 

 

Instruments and Controls

26

47711296 01-2019  © AB VOLVO PENTA

Summary of Contents for TAD1340VE











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands