manualshive.com logo in svg

Volvo Penta TAD1340VE, Operator'S Manual

Share
Download
Volvo Penta TAD1340VE Operator'S Manual Download Page 29

Display setting

settings for the display. Adjustment is made with the 

7

and 

9

 buttons; see DCU panel illustration.

•

Set contrast (%)

 - contrast setting.

•

Set backlight time (sec)

 - time setting (in seconds)

for display backlighting on, lighting is then shut off if
the panel is not used.

•

Set backlight brightness

 - display backlighting

brightness setting.

Information

shows the data for the engine and DCU.

•

Engine hardware Id

 - engine control unit part

number.

•

Engine software Id

 - engine control unit software

part number.

•

Engine dataset1 Id

 - engine data set 1 part number.

•

Engine dataset2 Id

 - engine data set 2 part number.

•

Vehicle Id

 - chassis number.

•

DCU hardware Id

 - DCU part number.

•

DCU software Id

 - DCU software part number.

•

DCU dataset1 Id

 - DCU data set 1 part number.

•

DCU dataset2 Id

 - DCU data set 2 part number.

 

 

Instruments and Controls

47711296 01-2019  © AB VOLVO PENTA

27

Summary of Contents for TAD1340VE











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands