Volvo Penta TAD1340VE Operator'S Manual Download

Page: 70 / 106

Alternator Belt, Replace

IMPORTANT!

Always change a drive belt which appears worn or
cracked.

1 Disconnect the main switch(es) and check that the

engine is not connected to system voltage.

2 Remove the fan guard and fan ring round the

cooling fan.

3 Remove the belt guard.

4 Insert a 1/2” square wrench in the belt tensioner (1).

Lift the wrench up and lift the water pump drive belt
off.

5 Insert a 1/2” square wrench in the belt tensioner (2).

Press the wrench down and remove the alternator
belts.

6 Check that the pulleys are clean and undamaged.

7 Press the 1/2” wrench in the belt tensioner (2) down

and install the new alternator drive belt.

8 Lift the 1/2” wrench in the belt tensioner (2) and

install the new water pump drive belt.

9 Install the belt guards.

10 Install the fan guard and fan ring round the cooling

fan.

11 Start the engine and do a function check.

2084

000

TAD1640GE-B, TAD1641GE-B, TAD1642GE-B, TAD1650GE,
TAD1651GE, TAD1640VE-B, TAD1641VE-B, TAD1642VE-B,
TAD1643VE, TAD1643VE-B, TAD1650VE, TAD1650VE-B,
TAD1651VE

2085

000

TWD1643GE, TWD1644GE, TWD1645GE, TWD1652GE,
TWD1653GE

Maintenance

47711296 01-2019 © AB VOLVO PENTA

Summary of Contents for TAD1340VE











































































































Search results

Summary of Contents for TAD1340VE

Reviews:

Related manuals for TAD1340VE

Brands by name

Popular brands

Volvo Penta TAD1340VE, Operator'S Manual

Search results

Summary of Contents for TAD1340VE

Reviews:

Related manuals for TAD1340VE

Brands by name

Popular brands