background image

1

USERS INSTRUCTIONS

1.1 GAS APPLIANCES

Gas Safety (Installations and Use) Regulations (UK).

In the interests of your safety and that of others it is a legal 
requirement that all gas appliances are installed and correctly 
maintained by a competent person and in accordance with the 
latest regulations.

1.2 ELECTRICAL SUPPLY

Please ensure that this appliance has been properly connected 
to the electrical supply by means of a double pole isolator or 
un-switched socket, and that the correct size of fuse (3 AMP) 
has been fi tted.

Warning: this appliance must be earthed!

  

1.3 GUARANTEE REGISTRATION CARD

Please take the time to fi ll out your guarantee registration card. 
The completed warranty card should be posted within 30 days 
of installation.

1.4 APPLIANCE COMMISSIONING CHECKLIST 
(UK only)

A checklist section can be found at the rear of the appliance 
installation booklet. This important document must be com-
pleted during the installation/commissioning of your boiler. All 
GAS SAFE registered installers carry a GAS SAFE ID card, 
and have a registration number. These details should be re-
corded in the Benchmark commissioning checklist section 
within the installation booklet. You can check your installers 
details by calling GAS SAFE direct on 08004085500. Failure 
to install and commission the appliance in accordance with 
the manufacturers instructions will invalidate the warranty. 
This does not affect your statutory rights.

1.5 HOW DOES IT WORK?

Your 

Mynute

 i

 boiler supplies heated water to your radiators 

and hot water to your hot water tank. The central heating is 
controlled via a time clock and any thermostats that your installer 
may have fi tted. The boiler will light when it receives a request 
from the time clock via any thermostat that may be installed.
Your Mynute 

i

 boiler lights electronically and does not have a pilot 

light. In the unlikely event of a fault developing with your boiler, 
the supply of gas to the burner will be terminated automatically.

Dear Customer

Your Vokèra Mynute 

i

 boiler has been designed to meet and exceed the very latest standards in gas central heating technology, 

and if cared for, will give years of reliable use and effi ciency.  
Please therefore take some time to read these instructions carefully.

Do’s and Don’t’s

Do

 ensure that the system pressure is periodically checked

Do

 ensure that the boiler should not be used by children or unassisted disabled people

Do

 ensure that you know how to isolate the appliance in an emergency

Do

 ensure that you are familiar with the appliance controls

Do

 ensure that your installer has completed the appliance log book section

Do not

 attempt to remove the appliance casing or gain internal access

Do not

 hang clothes etc. over the appliance

Do not

 forget to have the appliance serviced annually.

This booklet is an integral part of the appliance. It is therefore necessary to ensure that the booklet is handed to the person re-
sponsible for the property in which the appliance is located/installed. A replacement copy can be obtained from Vokèra customer 
services.

INTRODUCTION

1.6 DIMENSIONS

1.7 CLEARANCES REQUIRED

1.8 FROST PROTECTION SYSTEM

The 

Mynute 

i

 

is equipped with a built-in frost protection system, 

this enables the boiler to over-ride the time controls – even if 
switched off – and operate the burner and/or pump, should 
the temperature drop below 5

0

C for the main. In particular the 

burner will be in ON status until the main temperature reaches 
35°C for CH appliance.
Please note that the frost protection system is designed to 
protect the appliance only, should frost protection be required 
for the heating system, additional controls may be required.

NOTE

The frost protection system is reliant on the appliance having a 
permanent electrical supply, and being in a non-fault condition.

1.9 APPLIANCE STATUS INDICATORS

Your boiler is equipped with a large LCD display that indicates 
the appliance operating status. 

1. THINGS YOU SHOULD KNOW

Mynute 

i20

Mynute 

i30

HEIGHT

780 mm

780 mm

WIDTH

400 mm

400 mm

DEPTH

338 mm

388 mm

ABOVE

150 mm

BELOW

150 mm

LEFT SIDE

12 mm

RIGHT SIDE

12 mm

FRONT

600 mm

Summary of Contents for Mynute i20









































Reviews: