background image

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

PFW 6851

www.vogels.com

The adapter plate can be used with mounting patterns from 200mm x 200mm x to 650mm x 840mm.

In the event that you're flat panel has recessed or uneven mounting surface, universal spacers may be stacked to achieve proper spacing. Select the amount 

of universal spacer (s) that is closest in depth to keep your adapter plate as close to the flat panel as possible. The universal spacer must be secured between 

the flat panel and the adapter plates. 

Do NOT over tighten the screws.

Step 1.

  Determine if your flat panel will need the 

             adapter plates. 

Step 2.

  Locate the mounting points on the back 

             of the flat panel.

Step 3.

  Using a screwdriver, insert and tighten the 

              mounting hardware and adapter plates to the 

              back of the flat panel. Do not over tighten the 

              screws. 

Step 4.

  Place the universal mounting brackets over the

              threaded mounting studs that are on the 

              adapter plate.

Step 5.

  Place one (1) 5 / 16" flat washer onto each 

              threaded mounting stud.

Step 6.

  Thread one (1) M8 Nylon nut onto each threaded  

              mounting stud.

Step 7.

  Once the universal mounting brackets are level, 

              use a 1/2" socket and socket wrench to tighten 

              the M8 nylon nuts. Do not over tighten the 

              screws. 

Before tightening the nylon nut, be sure that both universal 

mounting bracket are level and aligned with each other. 

If they are not aligned and level, the flat panel will not sit 

properly when mounted to the PFW 6851

Adapter Plate

Griplate
Mounting Hardware

Flat Panel

Adapter Plate

Socket Wrench

Nylon Nut
Flat Washer

Universal Mounting 

Bracket

16

Adapter Plate Installation (Optional)

Page 8

Summary of Contents for PFW 6851











Reviews: