VKI Technologies Eccellenza touch Service Manual Download Page 38 | Manualshive

Page: 38 / 68

background image

S

ecti

on 5

- Cof

fee

&

P

ow

der

S

ys

tems

Service Manual

VKI Publication #100309-001

38

Removing Coffee and Powder Dispenser Motors

The coffee and the powder dispenser motors are the same component, with

the motor coupling configured differently. The coupling can be easily pushed

out of the motor housing with a 9/32 nut driver.

1.

Disconnect the inline wiring connector for the motor to be removed (circled in yellow).

2.

Remove the two screws securing the motor to be removed to the machine (red

arrows).

NOTE: When re-installing these screws, the torque must be 4 in/lbs for the coffee

motors, and 7 in/lbs for the powder motors.

3.

Remove the motor(s).

When removing or installing a coffee motor, the wiring (and the connector)

needs to be passed through the round opening in the coffee dispenser base.

To install a dispenser motor, follow these same instructions in the reverse order.

Coffee Motor Configuration

Powder Motor Configuration (default)

«
...
36
37
38
39
40
...
»

Summary of Contents for Eccellenza touch





































































Reviews:

No comments

Related manuals for Eccellenza touch

Brand: wacaco Pages: 7

NIZZA 1604A Business

Brand: Kaffit Pages: 40

Brand: Brew Express Pages: 20

Brand: Mixpresso Pages: 16

Brand: SnoWizard Pages: 5

Brand: U-Line Pages: 19

Brand: Follett Pages: 44

Brand: BALAY Pages: 76

Brand: Ice-O-Matic Pages: 2

Brand: Saeco Pages: 24

Brand: DèLonghi Pages: 26

Brand: Koldfront Pages: 13

Brand: DAK Pages: 19

Brand: BRAVILOR BONAMAT Pages: 28

Kaffeemaschine Robustica CJ-656B

Brand: Beem Pages: 72

Brand: Mr. Coffee Pages: 13

Brand: Prince Castle Pages: 9

Brand: Oster Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands