VKI Technologies Eccellenza touch Service Manual Download Page 56

Page: 56 / 68

ecti

on 7

- E

ctrical &

lectro

nic S

Service Manual

VKI Publication #100309-001

Removing the Control Board and Power Supply

Disconnect the service cord from the wall outlet prior to attempting to

replace any of the components in this section. Failure to do so can result in

an electrical shock!

The control board and the power supply are both mounted onto the same

support bracket.
To replace the power supply, the control board must first be removed from

the support bracket.

Control Board

With the back panel removed, disconnect all of the wiring harnesses from the control

board (

Disconnect the black wiring pair from the fuse holder (

Disconnect the white wiring pair from the main power switch.

Summary of Contents for Eccellenza touch





































































Search results

Summary of Contents for Eccellenza touch

Reviews:

Related manuals for Eccellenza touch

Brands by name

Popular brands

VKI Technologies Eccellenza touch, Service Manual

Search results

Summary of Contents for Eccellenza touch

Reviews:

Related manuals for Eccellenza touch

Brands by name

Popular brands