manualshive.com logo in svg

VKI Technologies Eccellenza touch, Service Manual

The VKI Technologies Eccellenza touch comes with a Quick Setup Manual for quick and hassle-free installation. You can easily download this comprehensive manual for free from our website, ensuring a seamless user experience. Get all the necessary instructions and maximize your product's potential with just a few clicks at manualshive.com.

Share
Download
background image

T

able

 of

 Conte

nts

 

Eccellenza Touch 

VKI Publication #100309-001

 

 

 

 

 

3 

Table of Contents 

SECTION 1 - Safety Information & Equipment Specifications .................................................. 5

 

Safety Symbols ...................................................................................................................................................... 5

 

Important Safeguards and Precautions ................................................................................................................ 6

 

Specifications ........................................................................................................................................................ 8

 

Capacities .............................................................................................................................................................. 8

 

Equipment Dimensions ......................................................................................................................................... 8

 

Installation Dimensions ......................................................................................................................................... 8

 

SECTION 2 - Care and Maintenance ........................................................................................ 9

 

Daily Care - Caretaker ........................................................................................................................................... 9

 

Every 10,000 Cycles or 12 Months - Service Technician ........................................................................................ 9

 

Every 3 Years - Service Technician ....................................................................................................................... 10

 

Miscellaneous ..................................................................................................................................................... 10

 

SECTION 3 - Error and Reminder Messages .......................................................................... 11

 

Clearing Error and Reminder Messages .............................................................................................................. 17

 

Fault Codes .......................................................................................................................................................... 19

 

Logs ..................................................................................................................................................................... 20

 

System Info .......................................................................................................................................................... 20

 

SECTION 4 - Brewer System ................................................................................................. 21

 

Replacing the Brewer Assembly .......................................................................................................................... 21

 

Replacing the Filter Screen .................................................................................................................................. 22

 

Removing the Brewer Piston & Seal .................................................................................................................... 23

 

Removing the Brewer Cylinder ............................................................................................................................ 25

 

Removing the Brewer Motor ............................................................................................................................... 29

 

Removing the Wiper Motor Assembly ................................................................................................................ 30

 

Removing the Motor from the Wiper Motor Assembly....................................................................................... 31

 

Removing the Wiper Motor Pinion/Coupling ...................................................................................................... 31

 

Removing a Wiper Motor Switch ........................................................................................................................ 32

 

SECTION 5 - Coffee and Powder Dispensing Systems ............................................................ 33

 

Coffee Dispenser Removal................................................................................................................................... 33

 

Removing the Grinder ......................................................................................................................................... 35

 

Powder Dispenser Removal ................................................................................................................................. 37

 

Removing Coffee and Powder Dispenser Motors ................................................................................................ 38

 

Whipper System Removal, Manual Cleaning and Installation ............................................................................ 39

 

Powder Rinse ....................................................................................................................................................... 44

 

 

 

Summary of Contents for Eccellenza touch





































































Reviews:

No comments

Related manuals for Eccellenza touch

1A Profi Handels Grill ECO AIR-PROFI SOUP DC-1400W Operating Instructions preview
Grill ECO AIR-PROFI SOUP DC-1400W
Brand: 1A Profi Handels Pages: 2
Kela Carolina Care & Safety Instructions preview
Carolina
Brand: Kela Pages: 17
Hoshizaki F-800MAF Service Manual preview
F-800MAF
Brand: Hoshizaki Pages: 61
Bloomfield GOURMET 1000 TM/MD 8792 Owner'S Manual preview
GOURMET 1000 TM/MD 8792
Brand: Bloomfield Pages: 24
Jenn-Air JUIFN15HX Installation Manual preview
JUIFN15HX
Brand: Jenn-Air Pages: 88
Saeco PURE HD8765 Operating Instructions Manual preview
PURE HD8765
Brand: Saeco Pages: 48
Delta BB 1350 Operating Manual preview
BB 1350
Brand: Delta Pages: 40
Saeco 714115344 Operating Instructions Manual preview
714115344
Brand: Saeco Pages: 40
LabelMill LM1510 Operation Manual preview
LM1510
Brand: LabelMill Pages: 65
wacaco Pipamoka Instruction Book preview
Pipamoka
Brand: wacaco Pages: 5
Kambrook Caf 3 in 1 Coffee Maker KDC120 Product Manual preview
Caf 3 in 1 Coffee Maker KDC120
Brand: Kambrook Pages: 10
Brady BMP 21-PLUS Quick Start Manual preview
BMP 21-PLUS
Brand: Brady Pages: 12
iGenix IG8127 User Manual preview
IG8127
Brand: iGenix Pages: 12
Oursson BM1010 Instruction Manual preview
BM1010
Brand: Oursson Pages: 154
Carimali CHOCO F Technical Instructions preview
CHOCO F
Brand: Carimali Pages: 33
Faema BARCODE Use And Installation preview
BARCODE
Brand: Faema Pages: 244
Saeco Group 200 Operation And Maintenance Manual preview
Group 200
Brand: Saeco Pages: 68
Hamilton Beach 80340 - Custom Grind Coffee Grinder User Manual preview
80340 - Custom Grind Coffee Grinder
Brand: Hamilton Beach Pages: 8

Brands by name

Popular brands

Load more brands