VKB-Sim Gunfighter Mk.II Quick Manual Download Page 4 | Manualshive

Page: 4 / 13

background image

4

VKB Gunfighter Mk.II Quick
Guide – HARDWARE

All Gunfighters come with the following cams in the box:

• #10 - soft center detent (factory installed)
• #30 - hard center detent

All Gunfighters come with the following springs in the box:

    • #10 - soft
    • #20 - standard (factory installed)
    • #30 - medium
    • #40 - strong

The Gunfighter Pro comes with an additional spring to support the 200mm extension:

• #50 - extra strong

The TM Warthog Adapter (optional; available separately) for Gunfighter comes with the following cam:

• "W" - to support the added weight of the TM Warthog grip (hard center detent)

«
...
2
3
4
5
6
...
»

Summary of Contents for Gunfighter Mk.II














Reviews:

No comments

Related manuals for Gunfighter Mk.II

Brand: e-BLEACH Pages: 24

Brand: MAKOT Pages: 6

Brand: Parkside Pages: 65

Brand: Vaillant Pages: 52

Brand: Vaillant Pages: 11

Brand: Rabbit Pages: 12

Brand: MIT Pages: 20

ISaGRAF mPAC Series

Brand: ICP DAS USA Pages: 75

Brand: W8ZR Pages: 77

Brand: National Instruments Pages: 31

Brand: Zaber Pages: 23

Brand: Watt Stopper Pages: 3

Brand: Sinclair Pages: 36

Brand: Automated Logic Pages: 10

Brand: Martin Audio Pages: 1

Brand: Thrustmaster Pages: 28

Brand: M2 Pages: 14

MAXinBOX FANCOIL 2CH2P

Brand: Zennio Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands