background image

 

 

condenser and evaporator. 

n

 

For installation, always contact the dealer or an Authorized service center. 

There is risk of fire, electric shock, explosion, or injury. 

n

 

Do not install the product on a defective installation stand. 

It may cause injury, accident, or damage to the product. 

n

 

Be sure the installation area does not deteriorate with age. 

If the base collapses, the air conditioner could fall with it, causing property damage, product failure, 

and personal injury. 

n

 

Do not let the air conditioner run for a long time when the humidity is very high and a 

door or a window is left open. 

Moisture may condense and wet or damage furniture. 

n

 

Take care to ensure that power cable could not be pulled out or damaged during 

operation. 

There is risk of fire or electric shock. 

n

 

Do not place anything on the power cable. 

There is risk of fire or electric shock. 

n

 

Do not plug or unplug the power supply plug during operation. 

There is risk of fire or electric shock. 

n

 

Do not touch (operation) the product with wet hands. 

There is risk of fire or electric shock. 

n

 

Do not place a heater or other appliance near the power cable. 

There is risk of fire and electric shock. 

n

 

Do not allow water to run into electric parts. 

It may cause fire, failure of the product, or electric shock. 

n

 

Do not store or use flammable gas or combustible near the product. 

There is risk of fire or failure of product. 

n

 

Do not use the product in a tightly closed space for a long time. 

Oxygen deficiency could occur. 

n

 

When flammable gas leaks, turn off the gas and open a window for ventilation before 

turn the product on. 

Do not use the telephone or turn switches on or off. 

PDF 

文件使用

 "pdfFactory Pro" 

试用版本创建

 

www.fineprint.cn

Summary of Contents for ACP-09CH25AEF













































Reviews: