EN
33
Avoid cleaning windows with a
thin jet once it might break the
glass. Set the sprinkler nozzle to a 45°
water outlet pattern.
4.4 - USING THE TURBO
LANCE
The turbo lance (24) is a useful
accessory that reduces the cleaning
time in rough surfaces and full of
debris. The turbo lance combines the
power of a thin jet and the efficiency of
a 25° angle.
Once the turbo lance performs a
powerful and thin jet, use it on
rough and impact-resistant surfaces
only.
The turbo lance is not adjustable
and cannot be used in detergent
application.
4.5 - DETERGENT
APPLICATION (FIG. M)
Using detergent reduces the cleaning
time and increase the efficiency on
stains removal.
Use high pressure washers
recommended detergents only.
Do not use other type of detergent or
chemical that might damage the pump
or seals and affect the machine’s safety
and performance.
Using thicker detergents, such as
dishwashing soap or car washing
shampoo might cause clogs in the
sprinkler nozzle.
Most car washing shampoos is a
combination of detergent and wax.
These tend to be viscous. Viscosity
increases in lower temperatures.
When using detergents combined
with wax or dishwashing soap, it shall
be diluted in warm water before using
and according to the recommended
instructions on the detergent.
To operate the machine with detergent,
you must follow these instructions:
1. Remove the detergent tank’s cover
(17), add detergent and install back the
cover;
2. Rotate the sprinkler nozzle (2)
clockwise until reaches its limit.
To use this machine with detergent you
must ensure an operation on minimum
pressure;
3. Use the regulating button (11) to
adjust the detergent outlet.
�
Vertical button - Detergent minimum
quantity;
�
Horizontal button - Detergent
maximum quantity;
4. Press the gun trigger (6) to clean;
In the end, press the gun trigger until
clean water starts running. Clean
the tank and the detergent filter. This
guarantees the complete removal of
detergent remains.
Always keep the aspiration filter
installed in the detergent
aspiration tube.
4.6 -TRANSPORT HANDLE
POSITION REGULATION
(FIG. N)
The transport handle (8) may be set
into two different positions. In the
superior position the handle will be
higher, in the inferior position, the
handle will be lower.
1. Press the transport handle locking
button (14);
2. Adjust the handle position;
3. Ensure the handle is locked. The
locking button must be out;
5. MAINTENANCE
INSTRUCTIONS
Before any maintenance or
cleaning work, place the
machine on a levelled surface,
disconnect the machine’s electrical
supply and release the water pressure.
To ensure a long service life and with no
issues, follow these instructions:
�
Wash the water and pressure hoses,
lances and remaining accessories
before assembly;
�
Clean dust and sand from the
connectors;
�
Clean the sprinkler nozzle regularly;
5.1 - WATER INLET FILTER
CLEANING (FIG. O)
Clean the filter regularly, once a month
or more frequently depending on the
times of use.
1. Untighten and remove the water inlet
filter (12);
2. Remove the filter element and wash
it with tap water until being completely
clean;
3. Insert the filter element on the filter;
4. Tighten the filter in the water inlet;
5.2 - LANCES’ SPRINKLER
NOZZLES (FIG. P)
The clog of the sprinkler nozzles (2,
25) causes a significant reduction in
the water flow, leading the machine to
an intermittent operation.
When it happens, follow these
instructions:
Lance’s sprinkler nozzle
1. Turn the machine off in the “ON/
OFF” switch (10) and remove the
power cable (15) from the socket;
2. Close the supply water tap;
3. Press the gun trigger (6) to release
the pressure on the hose;
4. Remove the lance (3);
