Vitek VT-8321, Manual Instruction

Page: 4 / 32

4
ENGLISH
•
The unit is not intended for usage by physi-
cally or mentally disabled persons (including
children) or by persons lacking experience or
knowledge if they are not under supervision of
a person who is responsible for their safety or
if they are not instructed by this person on the
usage of the unit.
• Do not use the unit if the power cord or the
plug is damaged, if the unit works improp-
erly or after it was dropped or in case of
leakage.
•
Do not use the unit if the power plug or the
power cord is damaged. If the power cord is
damaged, it should be replaced by the manu-
facturer, maintenance service or similar quali-
fied personnel to avoid danger.
•
Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction
is detected or after it was dropped, unplug
the unit and apply to any authorized service
center from the contact address list given in
the warranty certificate and on the website
www.vitek.ru.
• Transport the unit in the original package
only.
• Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature keep it for at least three hours
at room temperature before switching on.
• Unpack the iron; remove the protection from
the soleplate (14), if any.
• Check the unit for damages, do not use the
iron in case of damages.
• Before switching the iron on, make sure that
your home mains voltage corresponds to the
iron operating voltage.
•
There may be water residue in the tank, this
is normal, as the iron has undergone factory
quality control.
Note : While the first switching on the heating
element of the iron burns, therefore occurrence
of foreign smell and a small amount of smoke is
possible, it is normal.
WATER SELECTION
You can use tap water to fill the water tank (10).
If tap water is hard, use distilled or demineral-
ized water, this will prolong service life of the
iron.
Note: Do not fill the water tank (10) with scented
liquids, vinegar, starch solution, descaling
reagents, chemical agents etc.
FILLING THE WATER TANK
Before filling the iron with water, make sure that
it is unplugged.
• Set the temperature control knob (11) to the
position «OFF», and the continuous steam
supply knob (3) to the position «
• » – continu-
ous steam supply is off.
• Open the lid (2) and pour water into the water
tank (10) using the beaker (15) and then close
the lid (2) tight.
Note:
•
Do not exceed the « MAX » mark (13).
• If you need to refill water during ironing,
always switch the iron off first and unplug it.
• After you finish ironing, switch the iron off,
wait until it cools down completely, then open
the water inlet lid (2), turn over the iron and
drain the remaining water.
IRONING TEMPERATURE
Before operation, test the heated iron on a piece
of cloth to be sure that the iron soleplate (14) and
the water tank (10) are clean.
• Always check the recommended ironing tem-
perature indicated on the tag before ironing.
•
If the item label is marked with the symbol
, do not iron the item.
•
If there is no tag with recommended ironing
temperature, but you know the type of fab-
ric, use the following table to determine the
proper temperature.
Ironing temperature table
Icons Fabric type (temperature)
do not iron
• Synthetics, nylon, acryl, polyester
(low temperature)
•• Silk/wool (medium temperature)
••• Cotton (high temperature)
МАХ Linen (high temperature)
IM VT-8321.indd 4 24.12.2018 14:17:04