4
ENGLISH
service or similar qualified personnel to avoid
danger.
•
Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction
is detected or after it has fallen, unplug the
unit and apply to any authorized service center
at the contact addresses given in the warranty
certificate and on the website www.vitek.ru.
•
Transport the unit in the original package.
•
Keep the unit in a dry cool place out of reach
of children and people with disabilities.
THIS UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY. ITS COMMERCIAL USAGE AND USAGE IN
PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After the unit transportation or storage at low
temperature keep it for at least three hours
at room temperature before switching on.
Fan assembling
•
Unpack the fan and remove any advertising
stickers that can prevent its operation.
•
Check the unit for damages, do not use it in
case of damages.
•
Unscrew the clamp (22) from the lower part
of the bar (18), remove the flat washer (21).
•
Insert the lower part of the bar (18) into the
base (19), install the weighting compound
(20) on the lower part of the base (19), place
the flat washer (21) on the clamp (22) and
thread the clamp (22) clockwise. Make sure
that the base (19) is fixed firmly.
•
Unscrew the clamp (17) and extend the bar
(16) to the desired height and fix it by tighten-
ing the clamp (17) with a slight effort as you
turn it clockwise.
•
Install the motor unit (9) on the telescopic
bar (16), insert the fastening screw (13) into
the opening, thread the lock knob (15) clock-
wise and thread the motor unit (9) tilt lock (14)
clockwise.
•
Install the rear grid (7) on the motor unit (9),
the carrying handle on the rear grid (7) should
be turned upwards.
•
Fix the rear grid (7) on the motor unit (9) with 4
fastening screws (6) by screwing them clock-
wise until bumping.
•
Unscrew the fastening screw (5) halfway from
the blades (4).
•
Install the blades (4) on the motor axis (8),
match the groove on the motor axis (8) with
the fastening screw (5) and fasten the screw
(5) clockwise until bumping. Make sure that
the blades (4) are fixed properly.
•
Open 5 clamps (3) on the front grid (2).
•
Match the clamp groove on the front grid (2) with
the strengthening rib on the upper part of the
rear grid (7), match the openings in the lower
parts of the grids (2 and 7) and insert the screw
(1) into the opening. Fix the grids (2 and 7) with
the clamps (3).
•
Wind the nut on around the screw (1) and
tighten the grids (2, 7) holding the nut, fasten
the screw clockwise.
•
The fan is ready for operation.
USING THE FAN
•
Before switching the fan on, make sure that
the mains voltage corresponds to the unit
operating voltage.
•
Make sure that the fan is switched off. To do
this, set the switch (11) to the position «0».
•
You can change the tilt angle of the motor unit
(9). Turn the lock (14) counterclockwise to
loosen it and set the desired tilt angle of the
motor unit (9), fix the selected tilt angle turn-
ing the lock (14) clockwise.
•
Insert the power plug (12) into the mains socket.
•
Select the required blades (4) rotation speed
by turning the operation mode switch (11):
«0» - fan is switched off;
«1» - low blades rotation speed;
«2» - medium blades rotation speed;
«3» - high blades rotation speed.
•
Press the button (10) to switch horizontal rota-
tion of the motor unit on. To switch the rotation
mode off, pull the button (10) upwards.
•
To switch the fan off, set the operation mode
switch (11) to the position «0».
•
Remove the power plug (12) from the mains
socket.
MAINTENANCE AND CARE
•
Before cleaning the fan switch it off by setting
the operation mode switch (11) to the position
«0» and disconnect the power plug (12) from
the mains socket.
•
Do not use abrasive cleaners and solvents to
clean the fan.
•
Clean the motor unit (9) body with a slightly
damp cloth and then wipe it dry.
IM VT-1938.indd 4
1/10/20 4:31 PM