Vitek VT-1767 BK, Manual Instruction

Page: 4 / 44

4
ENGLISH
•
Do not move or tilt the unit during its opera-
tion.
•
Always unplug the unit and pour out water
from the water tank before cleaning or if you
do not use the unit.
•
Unplug the humidifier before moving it to
another place.
•
Do not touch the power plug with wet hands.
•
Before using the unit, closely examine the
power cord and make sure that it is not dam-
aged. Do not use the unit if the power cord
is damaged.
•
Do not dismantle the humidifier by yourself,
if any malfunction is detected, apply to the
nearest authorized service center.
•
Regularly clean the unit; do not allow scratch-
es to appear on the sprayer.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
Before the first use
Unpack the air humidifier and remove package
materials. Examine the humidifier for damages.
Do not switch on the humidifier in case of
damages.
Note:
–
If the humidifier was exposed to negative
temperatures, before switching it on for the
first time, keep it at room temperature for
30 minutes.
–
Use the humidifier at the room temperature
from +5° С to +40° С, and relative humidity
less than 80%.
–
Water temperature should not 40°С.
Before connecting the humidifier to the mains
make sure that the voltage of the electric network
corresponds to the unit operating voltage.
1.
Take the handle (9) and remove the water
tank (10) from the unit body (16).
2.
Turn over the tank (10), open the lid (13)
rotating it counterclockwise. Fill the tank (10)
with necessary amount of water, close the lid
(13) rotating it clockwise.
3.
Place the filled water tank (10) on the unit
body (16). Wait for some time, which is nec-
essary to fill the operating chamber with
water.
4.
Connect the humidifier to the mains, an icon
(24) will flash on the display (7), the room
temperature (19) and humidity (25) will be
shown.
5.
Switch on the humidifier pressing the “Power”
on/off button (1), the icon (24) will go out, the
display will switch to full brightness and the
mist release intensity icon (26) will appear.
Note:
–
Every pressing of the control buttons is
accompanied with a sound signal.
–
If no button has been pressed during 30 sec-
onds on the control panel or on the remote
control, the display brightness will decrease
automatically.
6.
To switch on the ionization mode, press
“Ozone” button (2), an icon (21) will flash on
the display (7). To switch off the ionization
mode, press “Ozone” button (2) again, the
icon (21) will go out.
7.
You can set necessary intensity by pressing
the “Max-Min” button for setting the mist
release intensity (3), the intensity will be
shown on the display (7) as a changing icon
(26).
8.
To switch on the water heating mode, press
“Heating” button (4), an icon (23) will flash on
the display (7). In this mode evaporable water
is preliminarily heated, which helps to disin-
fect the water and facilitates its evaporation.
Note:
–
Switching on this function may slight-
ly change the room temperature (19) and
humidity (25) indication on the display (7).
9.
To switch on the automatic humidity main-
tenance mode, press the “Humidity button
(5), the icon Humid will be flashing on the
display, press repeatedly the button (5) to set
the required humidity in the room (from 45
to 90%, setting step is 5%). In this mode the
icon “Humid” is flashing on the display (7),
and the following settings are shown: tem-
perature (19), humidity in the room (25) and
mist release intensity (26). To view the preset
humidity value press the “Humidity button (4)
once, flashing value of the preset humidity
will appear on the display (7), in 5 seconds
the information on the display will return to
the previous mode. To switch off the auto-
matic humidity maintenance mode, press the
“Humidity button (5) the required number of
VT-1767.indd 4 6/13/12 9:46 AM