background image

Safety Precautions

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). 
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To prevent electric shocks and risk of fire hazards, do NOT use other than with 

a specific power source.

The symbol is intended to alert the user to the presence of important        

operating and maintenance(servicing) instructions in the literature 

accompanying the unit.

The symbol is intended to alert the user to the presence of uninsulated

 "dangerous voltage" within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

 

Warning 

 

This equipment has been tested and found to comply with the limits for a Class

 A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

 to provide reasonable protection against harmful interference when the equipment

 is operated in a commercial environment. This equipment generates, uses, and 

 can radiate radio frequency energy and, if not installed and used in accordance with

 the instruction manual, may cause harmful interference to radio communications. 

 Operation of this equipment in a residential area is likely to cause harmful 

 interference in which case the user will be required to correct the interference at 

 his own expense.

 Caution 

 Any changes or modifications in the construction of this device which are not expressly

 approved by the party responsible for compliance could void the user's authority 

 to operate the equipment.

 Mains power quality should be that of a typical commercial environment. If the user

 of the model requires continued operation during power mains interruptions, it is 

 recommended that the model be powered from an uninterruptible power supply 

 (UPS) or a battery.

3

Summary of Contents for VIRTUOSO VTC-CB4MZ39













































Reviews: