vita Easyshade Operating Manual Download Page 9 | Manualshive

Page: 9 / 46

vita Easyshade Operating Manual Download Page 9

V I T A E a s y s h a d e

8

8. Continue to pull back on the Infection Control Shield,

stretching the shield at least 2-3 cm beyond the retainer at

the top of the probe. The material can withstand
considerable streching. It is important to have a uniformly
tight stretch and to avoid unevenness over the probe tip.

9. When the Infection Control Shield is stretched to its

maximum, pull the shield down over the retainer at the top
of the probe; then release the shield to secure it in place,
hooked on the retainer.

10. Verify that the Shield is stretched uniformly and flatly over

the face of the probe tip and that the shield has not torn
during the application.

11.

The shield should remain in place for all

measurements with the same patient. After single-patient
usage the shield should be properly disposed.

The photo shows an improperly positioned Infection Control
Shield. The shield is not stretched uniformly over the tip of the
probe. This non-uniform distribution of material over the probe tip

may cause inaccurate shade measurement.

«
...
7
8
9
10
11
...
»

Summary of Contents for Easyshade















































Reviews:

No comments