manualshive.com logo in svg

vita Easyshade, Operating Manual, Page: 6 / 46

Share
Download
vita Easyshade Operating Manual Download Page 6

V I T A   E a s y s h a d e 

5 

 

Touching the Next (“

►

”) or Previous (“

◄

”) indicators on the third bar causes the display to scroll through 

“Incisal ceramic” (for displaying, during the measurement of tooth areas, the result of the incisal measurement 
as a VITA ceramic enamel shade, EN1, EN2 or EN3) and “Incisal shade” (for displaying - during the 
measurement of tooth areas - the result of the incisal measurement as a VITA shade). The factory default is 

“Incisal ceramic”. These settings are only relevant for measuring tooth areas.  

 

 

Touching “Back” causes the “Tooth Single” screen to be displayed. Touching “Exit & Save” causes the changes 
to the settings (if any) to be saved as the power-on defaults. Touching “Next” causes the following screen to be 

displayed:

  

 

 

  

  
 
Touching the top bar, “Install Cal Block”, allows a new calibration block to be installed on the Easyshade. This 
will only be required if the calibration block that was shipped with the instrument is lost or damaged. Refer to 

Section 9.4 in the Appendix, “Replacing the Calibration Block”.  
 
Touching the second bar, “Self Test”, initiates an interactive test of Easyshade that is described in the Appendix 
in Section 9.1.  

 
Touching “Back” causes the “Translucency” screen to be displayed. Touching “Exit & Save” causes the changes 
to the settings (if any) to be saved as the power-on defaults. 
 

 

 

Note

:       If you have made changes to Easyshade settings on any of the Preset menus that you don’t want to save, you may abort the 

changes by turning off Easyshade. Throughout the Presets menus, and particularly if entering Calibration Block data, it  may 
be easier to activate touch-screen areas by using a Q-Tip rather than a finger tip. 

Summary of Contents for Easyshade















































Reviews:

No comments