manualshive.com logo in svg

vita Easyshade, Operating Manual, Page: 3 / 46

Share
Download
vita Easyshade Operating Manual Download Page 3

V I T A   E a s y s h a d e 

2 

1. Getting started 

 

  

VITA Easyshade

®

 provides accurate shade determination for natural and bleached teeth and a variety of 

restorations.

 

Easyshade displays its output on a touch-screen that is also used to make menu selections and 

enter data

.

 

 
  

1.1 Installation of the unit 

 

 

1. 

Open the Easysshade shipping container and remove the top layer of foam packing material. 

2. 

Remove the Easyshade base unit and hand piece and remove the protective plastic bags from those 
components.

  

 

3. 

Set the base unit down on a flat surface and rest the hand piece in the cradle. 

4. 

Plug the Power Cable into the rear of the left side of the instrument and into an appropriate power outlet.  
Easyshade is now ready to power up. Refer to page 1 “Quick Start Guide“ ot turn to section 1, “Getting 

started“, page 2. 

 

 

  

1.2 Power-up 

 

  
Turn on the Easyshade by pressing the power switch located on the left front of the unit.  The fan will turn on 
and the screen will display the Easyshade logo

.  

 

 

 
In the above screen, the three characters following “Release” (shown as underscores) identify the Software 

version.  The second three characters (also shown as underscores) identify the Shade Table version.  During 
lamp warm-up, the following screen is displayed:

 

 

  

  

  

When lamp warm-up is complete, the following screen is displayed:  

Summary of Contents for Easyshade















































Reviews:

No comments